QuoteReplyTopic: Pretipping with shrinkies Posted: August 16 2005 at 3:12pm
Ok, I just used only one side of the wand and just touched the part of the shrinkie the tip was next to. I did not "pre-tip" with the shrinkie, just got everything ready to install. So I had a pretip with a almost fully (98%) unshrunk shrinkie on the end of it. I'll post a pic, but I have to go get my kids from school first.
gsmilie, Can you explain how you heat just one side of the
shrinkie to the tip? I read this, but couldn't picture it.
Do you just touch the shrinkie and the tip to one side of the heat
wand? How do you do this without burning your fingers?
thanks!
gsmilie
Members Profile
Send Private Message
Find Members Posts
Add to Buddy List
Member
Joined: June 02 2005
Location: United States
Status: Offline
Points: 537
I found that if I put the tip into the shrinkie and heat only one side of the shrinkie to the tip, then put the shrinkie on the threader and slide shrinkie and tip up the natural hair shaft into postion then heat shrink the whole thing down. If I do this, I have not had any problems with the end of the tip sticking up past the shrinkie. Now, if I heat the shrinkie too long, sometimes it will squeeze the tip out and I have to do the whole thing over again.
Yes, it is a little time consuming, but in the long run it saves on frustration of having the tip pop up the top of the shrinkie.
To save time during the install, you could sit infront of the TV before hand, and do the tip attachements all at one time.
I like the pretipped hair, but its expensive, and even though it was pretipped I coated with LG.
I find it easy to get the placement of the shrinkie and tip easy when I
am doing it on someone else, but much more difficult on myself, so I
was looking for an easier solution --- make sense that two shrinkies
would be too bulky. Maybe I will try preplacing the tip in the
shrinkie with nail glue or clear nail polish.
You have to work the shrink while hot down so it's flush with the top of the tip. The way you tiped the hair is fine. Just need to work on placing the shrinkin the right spot
I agree, it's a great board, very informative. I tried the pretip LG with nail glue and then let them set for a day and then applied the shrinkie and heated it with the wand, then rolled it with my fingers. I think I might have tried two shrinkies but found it was too bulky. But then again my memory is sooo bad, so I could be mistaken. Many have been pleased with pretiping with LG and then nail glue and installing with shrinkies.
How do you like the pretipped hair? I hate to pretip!
I have read where a few tried this? How did it work?
I believe I read where someone used LG topped with nail glue, and then
applied a shrinkie over that, shrunk it down, rolled it, and then
placed this inside another shrinkie when attaching to the hair?
Did I read the thread right? How did this work? I also read
where some have glued the pretipped hair in the shrinkie with nail
polish or nail glue? So out of the two, which worked the
best?
I am new to DIY, and right now have Dr. Loc's pretipped HH that I
topped with LG and used shrinkies for install. I have black and
red 18". I've had these in for about 3 weeks and have been very
happy with them thus far. The most difficult part of the install
was having the pretips slip out the bottom of the shrinkie while
installing -- thus why I am asking about these other methods.
Thanks again for all the wonderful posts and information! This board is the best!
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum
Topic Options
Post Options
Thanks(0)
.
